An exit device is the one piece of hardware in a building that has to work for someone who is not thinking about hardware. That is the whole design brief: a person pushes, the door opens, no key, no thought, no second attempt. When a panic bar starts to drag or rattle, it is not a cosmetic complaint, it is the device telling you that something in a fairly simple mechanism has moved out of position.

What is actually happening when you push the bar

Strip away the variations and a panic device does one thing: converts a push anywhere along a horizontal bar into a pull on a latch. The push bar pivots or depresses, that motion drives a mechanism in the end case, and the latch retracts out of the strike so the door can swing.

Which latch it retracts depends on the type, and knowing which one you have makes the symptoms far easier to read:

  • Rim devices mount on the face of the door and throw a latch into a strike on the frame. The most common and the simplest.
  • Mortise devices sit inside the edge of the door and drive a latch in a mortise lock case.
  • Vertical rod devices drive rods up and down to latch into the head of the frame and sometimes the floor. Standard on pairs of doors without a centre post.
  • Concealed vertical rod devices do the same thing with the rods hidden inside the door, which looks better and makes diagnosis harder.

The faults you can read from the symptom

The bar feels gritty or needs a hard shove

Almost always friction rather than failure. Dust, grit and the sticky residue of old lubricant work into the end case and the latch, and the mechanism loses its easy travel. Door closers that have been wound up too hard contribute, because the door is being slammed into its strike thousands of times and the latch is taking that impact.

Worth knowing: a device that needs a genuine shove is a problem beyond maintenance. The point of the hardware is that it releases under a light push from someone who may be panicking, crowded or small. A bar that needs body weight is not doing its job even though it still opens.

The bar rattles when the door is shut

Rattle is slack, and slack usually means the latch is no longer sitting snugly in its strike. Either the strike has shifted, the latch has worn, or the door has dropped slightly on its hinges and is now presenting the latch at a different height. A rattling door also tends to be a draughty door, so the two complaints often arrive together.

The door does not latch on its own

This is the serious one, because a door that is not latched is not secure and, on a fire door, is not performing. The usual causes, in order of how often they turn up:

  1. Closer not finishing the job. The latch speed is set too low and the door arrives without enough momentum to drive the latch home.
  2. Misalignment. The latch is hitting the edge of the strike or the frame instead of entering cleanly. You can often see the witness marks.
  3. Dogged device. Many rim devices can be held retracted deliberately for daytime use. Someone dogged it and nobody undogged it. Check this first, it costs nothing.
  4. Rod adjustment. On vertical rod devices, rods that have drifted out of adjustment stop reaching the strikes properly, particularly at the top.
  5. Worn latch or strike. Enough cycles will round off the latch bolt until it no longer holds.

The alarm sounds or the device is noisy in operation

Some devices include a local alarm, a delayed egress function or an electric latch retraction. Those add wiring, power supplies and interfaces to the fire alarm system to the list of things that can be wrong, and they move the job out of pure mechanical territory. A device with an electrified function that has started behaving oddly should be looked at by someone who will check the power supply and the interface, not just the hardware.

What is adjustable, and what is not

A good deal of what looks like failure is adjustment. Strike position, closer latch speed, rod length on vertical devices, and the alignment of the door in its frame are all things that can be set correctly without new parts. Cleaning and correct lubrication of the end case recovers a surprising number of gritty bars.

What is not adjustable is wear. Once the latch bolt is rounded, the mechanism inside the end case is worn, or the bar itself is bent, the device is at the end of its life. The same applies when the door has deformed: a steel door that has been forced, or has taken a hard impact, may no longer be flat enough to present the latch consistently, and no amount of hardware adjustment fixes a twisted slab. Where there has been a forced entry, the right order is to deal with the break-in damage to the door and frame first and only then expect the exit device to behave.

The thing that gets missed

Exit devices are sized and specified for a particular door, frame and application. A device that was swapped in because it was the one on the van may fit the holes and still be wrong for the door: wrong function, wrong handing, wrong length for the door width, or not rated for the application it has ended up in. If a device has been replaced at some point and has never worked properly since, that mismatch is worth checking before chasing adjustments that cannot win.

Keeping on top of it

Exit hardware responds well to being looked at on a schedule rather than when it breaks. A short routine covers most of it: push the bar and feel the travel, let the door close on its own from several positions and confirm it latches every time, check the device is not dogged when it should not be, look for witness marks around the strike, and confirm nothing is blocking the door’s swing or the route beyond it.

Anything beyond that, and in particular anything involving a fire-rated assembly, belongs with someone who works on this hardware regularly. Requirements for inspection and record-keeping on fire door assemblies vary by jurisdiction and by building type, so confirm what applies to your premises with your local authority having jurisdiction rather than assuming. A contractor who handles commercial door repairs as routine work will know what the local expectations are and what documentation you are supposed to keep.

Frequently asked questions

Can I oil a stiff panic bar myself?

Light cleaning and the correct lubricant on the right parts is reasonable maintenance. The caution is that heavy oils attract grit and make the problem worse a few months later, and that a bar which is stiff because of wear or misalignment will not be fixed by lubricant. If it comes back quickly, something mechanical is wrong.

Why does our door latch in the morning and not in the afternoon?

Usually temperature. Frames and doors move with heat, and a latch that only just reaches its strike when cool may miss it entirely once things have expanded. It points to an alignment margin that is too tight rather than a faulty device.

Is it acceptable to prop a fire exit door open in hot weather?

No. A fire door only works closed and latched, and propping it defeats the assembly entirely. If a door needs to stay open for airflow or traffic, the proper solution is a hold-open device linked to the fire alarm so it releases automatically, not a wedge.

The bar works but the door is hard to pull shut. Related?

Often yes. Both can come from the door being out of square in its frame, which makes the latch bind on its strike and the door rub on the way to closed. Worth looking at the hinges and the frame before touching the device.

How fast should a failed exit device be dealt with?

Immediately if it does not open on a push, since that is a life safety problem. Quickly if it opens but no longer latches, because the door is neither secure nor fire-performing in that state. If a device has failed outside working hours on a door that cannot be secured, that is what emergency door repair exists for.