Property managers in Toronto juggle a long list of building systems, and doors rarely get attention until one fails. A lobby door that will not latch, a fire exit that sticks or a closer that slams can turn into a security problem, a tenant complaint or a fire inspection issue overnight. A simple annual door audit catches most of these problems early. Here is a practical checklist you can use across a condo, office, plaza or industrial building.

Why a Door Audit Pays Off

Commercial doors are among the hardest-working components in any building. A busy lobby or retail entrance can cycle hundreds or thousands of times a day. Hardware wears gradually, and small problems, like a closer that has started to leak or a hinge with a loose screw, quietly make other parts work harder. By the time someone calls in a failure, several components are often damaged.

An audit turns emergency repairs into planned work. It also gives you a record of which doors keep failing, which is the best evidence for upgrading hardware rather than repairing it again and again.

Step 1: Build a Door Inventory

List every exterior door, every fire-rated door and every high-traffic interior door. For each one, note:

  • Location and use (main entrance, stairwell, garage vestibule, service door).
  • Door and frame material (aluminum and glass, hollow metal, wood).
  • Lock or exit device type, closer type and hinge type.
  • Whether the door is fire-rated, and whether the label is still legible.
  • Any repairs in the past year.

Even a basic spreadsheet makes the rest of the audit much faster.

Step 2: Check How Each Door Closes and Latches

Open each door fully and let it close on its own. Watch and listen.

  • Does it close completely and latch every time, without help?
  • Does it slam, or close so slowly that it never latches in wind?
  • Is there oil on the closer body or the floor beneath it?
  • Does the door drag on the floor or rub on the frame?

A closer that leaks oil or has lost control of closing speed should be repaired or replaced. On fire doors, a door that fails to close and latch is a serious issue.

Step 3: Inspect Exit Devices

Push every panic bar or exit device. It should release with one smooth push and relatch when the door closes. Look for bent push bars, loose mounting screws, sticking latch bolts and dogging that no longer holds. Exit hardware is life-safety equipment, so any problem goes to the top of the list. If you find worn or damaged devices, a specialist panic bar and exit device repair service can repair or replace them with compliant hardware.

Step 4: Look at Hinges, Pivots and Frames

Lift gently on the latch side of each door. Any vertical movement means worn hinges or pivots. Look for gaps that are wider at the top than the bottom, a sign the door is sagging. Check frames for dents near the strike, rust at the bottom of hollow metal frames and loose anchors in storefront framing.

Step 5: Check Locks, Keys and Access Control

  • Do all keys work smoothly? Are there cylinders that bind or stick?
  • Is the key list up to date? Do former staff or contractors still hold keys?
  • Do electric strikes and mag locks release reliably on every credential?
  • Do request-to-exit devices and emergency releases work as intended?

Step 6: Check Hardware Grade on Problem Doors

When the same door fails repeatedly, the hardware is often under-specified for its traffic. Residential or light-duty components on a busy commercial entrance will not last. This explainer on commercial door hardware grades in Ontario covers what Grade 1, 2 and 3 mean for locks, closers, exit devices and hinges, and which grade belongs on which door.

Step 7: Seals, Thresholds and Glass

Check weatherstripping and door sweeps on exterior doors, especially before winter. Look for cracked or chipped glass, loose glazing stops and damaged thresholds that create a trip hazard. In Toronto, salt and freeze-thaw are hard on thresholds and the bottom of frames.

Step 8: Prioritize and Schedule

Sort what you found into three groups:

  1. Urgent: fire doors that do not close or latch, exit devices that do not release, exterior doors that do not lock.
  2. Soon: leaking closers, sagging doors, worn hinges, sticking cylinders.
  3. Planned: hardware upgrades on doors with repeat failures, cosmetic frame repairs, seal replacement.

Many property managers find it easier to hand the whole process to one contractor with a scheduled program. A commercial door maintenance program in Toronto typically includes regular inspections, adjustments and a running record of each door, which also helps with fire inspection paperwork.

How Often Should You Audit?

At least once a year for the whole building, plus a quick pre-winter check on exterior doors. High-traffic entrances and fire doors benefit from more frequent checks. Fire doors and closures also have ongoing inspection and maintenance requirements under the Ontario Fire Code, so keep notes of what was checked and when.

Frequently Asked Questions

Can building staff do the audit?

Yes, a basic walk-through can be done by trained building staff. Repairs and adjustments to closers, exit devices and fire door hardware are best left to a qualified door technician.

What is the most common problem found?

Closers that are leaking or badly adjusted, and doors that no longer latch because of sagging hinges or worn latches.

Should we replace or repair failing hardware?

If a component has failed more than once on the same door, upgrading to heavier-duty hardware is usually cheaper over time than repeated repairs.

Bottom Line

A structured door audit takes a few hours and can save a building from emergency calls, security gaps and inspection problems. Inventory your doors, test how each one closes and latches, check the exit hardware, look for repeat failures and schedule the work. Your tenants will notice the difference, even if they never notice the doors.